Kimwipes + Lens Fluid Station - Backstage cart lip (one piece, strongest)
======================================================================

What it holds: Kimwipes 34155 small box opening-up, plus a 43-46 mm lens-fluid bottle

PRINT SETTINGS
  Filament:  PETG
  Walls:     5
  Infill:    35% gyroid
  Orientation: the files are already oriented for printing. Put them on the plate as they load;
               don't rotate them.

FILES AND SUPPORTS
  - clip_NA_K_kimwipes_fluid_dock.stl  (supports: yes)
  - clip_NA_R_fluid_cup_reducer.stl  (supports: no)

HOW IT MOUNTS
  BACKSTAGE CART LIP (ONE PIECE, STRONGEST)
    The cart-lip slot is printed into the holder, so it is one piece and as strong as it gets.
    Hold it tilted, hook the slot over the upright lip on the edge of a Magliner / Backstage-style cart
    shelf, and rock it down until it sits flat against the side.

    Notes for this holder: Default: one piece with the Magliner/cart lip mount, strongest. Prints upright, tree supports under the flange only; optional 2 x M5 thumbscrew lock. The reducer sleeve is for 35-37 mm bottles.

HOW IT WORKS
  For camera ACs and DITs: the small Kimwipes box (KimTech 34155, about 118 W x 121 D x 73 mm tall) stands opening-up in a shallow sleeve on the outside of the cart, long side along the cart. The sleeve is 58 mm deep, so the top 15 mm of the box stands above the rim and the box top sits about 20 mm above the deck: the pop-up tissue is right at hand and the box stays clean and uncrushed. Two crush ribs on each side wall and two on the front hold the box snug (121.5 x 118.3 mm between ribs), so it can't bounce out on a push. To refill, grab the exposed top of the box and lift, or push it up through the 34 mm thumb hole in the floor. A window in the front shows the box.
  Beside it, a 46 mm cup 70 mm deep (its rim 17 mm above the deck, 12 mm above the sleeve) holds a lens-cleaning fluid bottle (Pancro 4 oz class, about 43-45 mm). A flex tongue with a grip rib on the outer side presses the bottle against the cart-side wall, so it doesn't rattle. For 35-37 mm (2 oz class) bottles, drop in the reducer sleeve (included). Drain holes in both floors for rain.
  Cart facts

  - Sticks out 130.8 mm from the cart side (the box is 118 mm deep, so the sleeve can't be slimmer)
  - Hangs 56.0 mm below the deck
  - Flat cart side needed below the lip: 56.0 mm
  - Overall 148.5 x 178.9 x 98.0 mm
  - Sleeve rim 5 mm above the deck; the box top about 20 mm above the deck
  - Put it on a cart end, not a side that goes through tight doors (130.8 mm out)
  Retention: held by gravity unless you fit the M5 thumbscrew. A short M5 heat-set insert (6.4 mm hole, 9 deep) goes into the deck-side face of the inner flange; a nylon-tipped M5 thumbscrew through it clamps the lip, so the part cannot lift off on a bump or a lift-gate drop, slide along the lip or rattle. Check your lip is at least 16 mm tall first. Two M5 insert holes (45 mm either side of centre).
  Fits: Backstage Equipment and Magliner-style carts with a 3.4 mm upright shelf lip. The mount drops onto the lip from above: 3.7 mm slot (0.3 mm clearance), 26.6 mm deep with a round end, 0.5 mm chamfers at both slot ends.

OTHER MOUNTS
  The same holder also comes ToughBuilt bar (one piece), Dock (swap between mounts), Mountless (desk, shelf, case or screw to a panel). Pick the mount on the site: https://cart-tools.sdos-placeholder.workers.dev/#na-k-kimwipes-fluid-dock

TEST THE FIT FIRST
  Carts, bars and tape rolls vary a little. Before a long print, print the small fit test from the
  Test pieces section of the site (or this part at low infill) and check it on your own gear.

Not affiliated with or endorsed by Magliner, Backstage Equipment, ToughBuilt, Milwaukee, Hollyland, Eartec, Sekonic, Inovativ, Matthews or Manfrotto. Brand names only say what a holder fits.
